[HELP] NCK BOX / Dongle Premium v2 HELP How to USE/UNLOCK/Flash/Install - Info & PDF

1. Download from support archive with custom recovery.
1.1.If drivers installed skip step 2.
2. Power on phone complete and install drivers, must be mounted volume with phone drivers, so install from this volume.
If custom recovery already flashed go to step 9.
3. Put phone in FastBoot mode holding Vol- and power On(5-10sec)
4. Put usb cable and wait until install drivers(check in device manager if all ok).
5. Open nckbox.exe, select Fastboot_utils tab.
6. Tick flash phone in recovery utils.
7. Click on load and send and select recovery image.
8. Wait until finish, remove cable, remove battery(for 5...6 sec, if not phone will auto power on).
9. put battery, keep Vol+ and power on until phone power in recovery mode.
10. Go to Huawei android tab, select correct model and press check.
11. If all ok press unlock.

PS
Unlock need make from recovery mode.

How to Install Drivers for NON Test Point Models:

1. Go to X10 DRIVERS
2. Select the correct 32 bit or 64 bit shortcut folder for your Operating System
3. First run "SEMC Flash Driver Install"
4. Complete the install wizard that appears
5. Second run "ADB Driver Install"
6. Complete the install wizard that appears
7. Next we need to connect the X10 in Flash Mode (some times called boot mode)
8. Remove the battery for 10 seconds and replace
9. With the phone still powered off, Press & HOLD the "Back Button"
10. Still holding the Back Button connect the USB cable
11. Windows will now detect the new hardware and automatically install the drivers.
12. Once complete, remove the USB cable from the phone and power the phone on.
13. Next we will connect the phone with "USB Debugging" Enabled
14. On the phone go to "Settings"
15. Next go to "Applications"
16. Next go to "Development"
17. Now enable "USB Debugging"
18. Click "OK" to confirm enabling of USB Debugging
19. Now connect the USB cable
20. Windows will now detect the new hardware and automatically install the drivers.
21. Once complete you can proceed to unlock your X10, X8 etc...

Follow Instructions on Screen.

Now we can proceed to Unlocking the X10, X8, etc...

1. Now click on the "SE" tab of the software
2. Please make sure SIM card is removed from the phone
Please make sure SD card is inserted in the phone before unlock !!!!!!!!
3. Make sure that your phone is running a later version of ANDROID that 1.6 (tick the box to confirm on the Unlock Client) or ....
4. If you are unsure if your phone is running v2.1 or later, then connect the phone in USB Debugging Mode & click "Check Phone"
5. Ok, we now know we are running ANDROID 2.1 or above (if you are not then please upgrade your phone and start again)
6. Remove your phones battery for 10 seconds and replace
7. Press and HOLD the phones back button
8. While still holding the phones back button connect the USB cable.
9. The unlock client will now start the unlock process
10. When prompted by the UNLOCK SOFTWARE, remove the USB cable and power on the phone.
11. Make sure the phone is in USB Debugging Mode and connect the USB Cable again
12. The SOFTWARE will now complete the unlock

Please make sure:
• Warning! Please make sure SIM card is removed from the phone
Please make sure SD card is inserted in the phone before unlock !!!!!!!!
• Your X10i is NOT running ANDROID V1.6 (please update your phone if it is before unlocking, do not attempt to unlock V1.6)
• Your X10 is running Android 2.1 - 2.3.
• You have a Standard NON modified Kernal on your phone (you have not flashed custom firmware to your X10)
• You must make sure PHONE IS NOT ROOTED BEFORE UNLOCK.
• You must have internet connection

Trouble Shoot:

Unlock Not OK or Not Detecting Phone?
Possible causes:
1. On Vista or Windows 7 32/64 byte OS, client must be run as administrator (right click on shortcut, select "run as administrator")
2. Firewall or Antivirus is deleting files in the “loaders” folder. Uninstall software turn off antivirus and reinstall.

Phone shows no service after unlock:
1. Remove Battery and wait 1 minute. Insert Battery and power on phone.
Software hangs while unlocking or detecting ADB device
Antivirus has deleted important files. Uninstall software.Turn off Antivirus .Download and install software again

[FAQ]

Q - Are the Xperia x10 mini Pro & Xperia Mini Pro the same
A - No, the Xperia Mini Pro is a newer Phone, if you are unsure please check the label under the battery, the X10 mini and X10 Mini Pro are both supported (u20 & u20i)

Q - Is it a permanent unlock
A - Yes

Q - My X10 unlock counter is blocked
A - No problem, your X10 will still be unlocked.

Q - If I flash the phone, the phone will get relocked ?
A - No it's a permanent unlock, not a stupid "patch" unlock solution

For Test Point Unlocking Models:

1. Connect phone powered on to your PC
2. Install necessary drivers (drivers are located in "Program Installation Folder" folder)
3. Disconnect battery,press Unlock
4. Attach Testpoint and connect phone with Micro USB cable directly to motherboard USB port, Install drivers ( if it s installed the drivers as ZEUS FLASH DEVICE (WRONG) so to fix:

• Go to device manager
• Click on Universal Serial Bus Controllers
• Then right click on zeus flash device
• Select update drivers
• Install drivers from nck folder.(C:\NCK Dongle\NCK Dongle\test point drivers), until it detects Qualcomm HS-USB QDLoader 9008

5. Don't use USB hubs!.
6. Follow software instructions (prompts)


Trouble Shoot:

Unlock Not OK or Not Detecting Phone?
Possible causes:
1. On Vista or Windows 7 32/64 byte OS, client must be run as administrator (right click on shortcut, select "run as administrator")
2. Firewall or Antivirus is deleting files in the “loaders” folder. Uninstall software turn off antivirus and reinstall.

Phone shows no service after unlock:
1. Remove Battery and wait 1 minute. Insert Battery and power on phone.
Software hangs while unlocking or detecting ADB device
Antivirus has deleted important files. Uninstall software.Turn off Antivirus .Download and install software again

Read codes procedure via NCK Box + NCK Box Generic MTK Flash Tool

1. Select model
2. Select com port (if phone have microUSB port, use GW300 cable)
3. Press Backup sec(alcatel) button
4. After backup done, fill IMEI window
5. Press Load backup and calculate button
6. Open backup file (NCK BOX/NCK BOX Generic MTK Flash Tool/alcapid_backup/phone model/XIB3CG22.nsb)
7. Exe read codes from backup
8. Put not accepted sim in phone and enter NCK code > unlock done



br.
NCK Team

let s take OT-800 as an example:

OT-800X-PMPT1

How do we name flash file:

OT-803 - name of the model, in our case it's Alcatel One Touch 800
X OR A OR D etc.. - base-band settings ("A": 850/1900 band, "X": 900/1800 band & "D" Dual SIM).
PMPT1 - Provider ID (firmware branding) usually it is written like this 2XPMPT1 but we take the main letters of provider id which is the last 5 letters.
XR46CP1A - Secro Name: Security block version.
Locked - means that after flashing phone will be locked.
Unlocked - means that after flashing phone will be unlocked.
Samsung OR ONYX OR any other flash chip name - is the flash IC chip inside phone so you must flash with same firmware for this flash chip.
IF AFTER OT (ONE TOUCH) you see the letter V - example OT-V this mean Vodafone Phone : OT-V555 = Vodafone-555.

BR

NCK Team

Here we will upload videos related to NCK Products.

How to flash BB5 Phones:

NCK BOX - How to flash bb5 phone with usb cable - YouTube

4unlockers.com - NCK Dongle Nokia E52 USB-Flashing - YouTube

How to Unlock Nokia BB5 Phones with UFS as Interface

NCK BOX - How to Unlock Nokia BB5 Phones with UFS as Interface - YouTube

F1310 Unlocking Video

ZTE F1310, Unite F1310 - ????????????? ?? ????????? - ???????? - unlock - YouTube

Enjoy with

NCK Team

ZTE V768 Unlocking By NCK Team

ZTE V768 Unlocking By NCK Team - YouTube

BR

NCK Team

Unlock ALCATEL OT-255a with NCK DONGLE BOX

Many users have problems with the smart card drivers in Win7 64 bit. The problem is that the smart card driver is not installed properly, therefore removing the dongle/box after inserting again, windows tries to reinstall the driver, but fails.



Here is the 100% solution and the files:

4shared link: NCK_SmartCard_Driver_Win7_64.zip
mega link: NCK_SmartCard_Driver_Win7_64.zip

Proper driver installing, step by step:
BR
NCK Team

Q.-I'am have normal mtk phone and this phone not listed, how to solve?
A.-Possible your phone is supported already.
NCKBox generic mtk exe support many CPUs and phones can be supported but not listed in NCK Software


How to do:

1:- First try to see if phone can be connected by USB (easy way)
To connect by USB phone must be in boot mode.
1.2:- To connect phone by USB, phone must be off and need to press some key and insert USB cable or simple power off phone and insert USB cable.
Device manager must be opened.
First need to try with powered off phone, connect USB cable.
If all ok, lcd will remain blank and in device manager will be created new com port.
If this method not work then:

1.2.1:- Phone off and try with "MENU" button and insert USB cable
OR
Phone off & Press * Key and insert USB cable
OR
Phone off & Press # key and insert USB cable,
OR
Phone off & Press CALL button and insert USB cable, and so on(can be any key, mostly used in phones is menu, *, #, left soft key, right soft key, call button, vol-, vol+)
After each try need reinsert battery.
On success will be created new virtual com port.
Remember combination and start exe.
Select USB and press read info in service@unlock tab.

Some phones will display real code, some will display 12345678(default one) and lock status.

If READ info is OK and code is default(12345678) must be used direct unlock.

Q- MTK phone stuck on boot logo, need to flash phone?
A- Usually not need to flash,many times help simple auto fat format from exe and after need to restore imei.

Q-Phone have user code enabled and exe not display user code.
A-Universal way: auto fat format from exe and after need to restore imei.
Recomened way: backup calibration, auto format fat, restore calibration.
On this opperation usually gone all user stuff, if this is important need to backup first using FILEMANAGER.

Reading Phone Info/User Lock
- Reading Phone Information and Phone Lock is very easy with NCK Box.
- Connect phone with USB Cable or RJ45 TP Cable and select proper port in CDMA Module.
- Click on Read Info. A detailed phone information will be shown.




Doing SP Unlock
- Connect Phone with USB Cable.
- Select correct Model or just click Read Info, it will automatically select correct Model.
- Click on Unlock and it will be unlocked.



Flashing Phone
- Select correct Model.
- Select Correct Flash File.
- If you are connecting phone in Emergency Mode ( 5 + PWR ) then tick Emergency Mode.
- In both Normal and Emergency Mode, software will automatically detect correct model, and will notify you if you chose wrong model.
- Click on Flash.



Repair Phones Blinking on LG Logo
- Connect Phone in Emergency Mode. ( 5 + PWR )
- You dont need to select any proper model as software will automatically detect correct model.
- Click on Blink Repair and you are done.



Writing RF/PRL/EFS Data After Flash/Blink Repair
- Connect Phone in Normal Mode.
- Select correct model, and tick RF / PRL / EFS and click on Write.
- Phone will reboot when done.



Repair/Write MEID/ESN
- Connect Phone in Normal Mode.
- Select option like ESN or MEID.
- Enter a valid ESN or MEID.
- Click on Write and you are done.



Some Advance Features available only in NCK Box CDMA Tool
- It can automatically identify if selected file is a valid Qualcomm Firmware and display file type (QSC60xx/QSC11xx).
- It will warn you if you select wrong Model and will select correct model automatically. Preventing you from killing your phone.
- If you are flashing your phone in Emergency Mode, it will read your phone model in Emergency mode and will warn you if you have selected wrong model.
- Unique EFS Writing Method lets you do it by simply clicking a button. No need to select anything. Our tool is smart enough to select things needed for your model.

Br,
NCK Team

Android MTK hints.

Q- My phone show invalid imei, how to solve.
A- If phone have OTP imei (alcatel as example) then simple reflash phone, imei will come.
If phone not have OTP imei then will need to repair imei.

Q- I'am maked repair imei, but after wipe phone imei reset back to default or null, how to solve?
A-In android mtk phones imei and other settings is stored in nvram partition and cached in data(userdata) partition.

When user wipe phone /data/nvram remaked from /nvram partition.
Many free tools repair imei only in /data/nvram, but in /nvram remain still empty imei and after wipe phone imei will become empty.

How to solve:Need to rebuild imei in corect way in /data/nvram and /nvram
If nvram have many damaged blocks, need to write good nvram file from other phone, same model and after make rebuild imei.

Damaged NVRAM simptoms:
Empty imei, phone not recognize sim card, network is not stable or missing, phone loop on boot logo, phone reboot in recovery after power on, wifi not work or work in strange ways.

[FAQ] My Alcatel Android phone have null IMEI. How to solve?

---

All Alcatel phones have IMEI in OTP area.
This mean IMEI, can't be destroyed by software.

Sometimes we have null imei.
This can happen usually in next cases:

1. Security corrupted: Full flash with format usually solve this.
2. NV area corrupted: Need to erase nv area and after perform flash with format.
3. Incompatible hardware modem with modem firmware:Need to write correct version.
4. Hardware damage, in this case need to repair phone.

How to know initial phone version if phone come already damaged:

Need to read PRO_INFO partition.
Make boot info with display partition info checked.
In long list will be line with PRO_INFO begin and end adreses.
Need to use this adreses and to read firmware using this values.
After upload in forum or use hex editor.

Version and phone name are in plain in this partition.